Kenwood P-W121B 2 Inch Car Loaded Sealed Subwoofer & 500W Amplifier Package
2 Inch Car Loaded Sealed Subwoofer. 2-channel amplifier and sealed enclosure. Terminals: spring post terminals (one pair).
Mounted on the left side of the enclosure; will accept pin connectors. Single or dual banana plugs (3/4 width), or bare wire up to 10 gauge. Auto Turn-on: When using a speaker level input, the amp will turn. On automatically when it senses the input signal. Crossover: The amplifier has a fixed 80Hz low-pass filter with.
A slope of 18dB per octave. The filter can be turned On or Off as. Should be turned on to power the included subwoofer. Bridgeable: This two-channel amplifier is bridged to.
The 4 mono subwoofer load; the bridged output is 170 watts x 1 channel RMS. Power Connections: The power, ground, and remote turn-on connections. Are 0.425 wide screw terminals. A Phillips-head or flat blade screw driver.(not supplied) is required to tighten/loosen the terminals. Minimum 10 gauge wire is required for power and. A 25-amp fuse should be placed on the power wire within.
18 of the battery terminal. Speaker Outputs: The two pair of speaker outputs are 0.315 wide. Connectors are also recommended for the speaker wires. Line Level Input: The line input is a pair of stereo RCA jacks. Speaker Level Input: A 9 wiring harness is included for the speaker level input. Gain: To accommodate the varying range of signal levels from. Today's factory and aftermarket radios, the KAC-5207 features. An adjustable gain control; 0.2-5.0 volts line level (RCA). And 4.0-12.0 volts speaker level. Power Indicator: The Power indicator (on top of the amp) lights. Up when the amplifier is turned on. This indicator turns off with. The amplifier, and will turn off if the amplifier goes into protect mode. Protection circuitry: The amplifier features protection circuits that. Will turn the amp off in case of the following events. Unit malfunctions and DC is sent to speaker output. Cast Aluminum Heat Sink: The KAC-5207 utilizes a cast aluminum. Heat sink design to ensure the amplifier stays cool. Fuse: The amplifier uses a 25-amp ATO blade-type fuse.CTA-2006 Compliant: CTA-2006 is a system of testing and. Measurement for mobile audio amplifiers. Advocates a uniform method for measuring an amplifier's RMS. Power output and signal-to-noise ratio.
Allow consumers to compare car amplifiers and receivers. Under the same conditions (apples to apples). Criteria, the Kenwood KAC-5207 is rated at 70 watts RMS x 2 channels.With an 80 dBA signal to noise ratio. The signal to noise ratio at the. Rated power output (not CTA-2006 conditions) is 100 dB. Sensitivity: 84dB / W / m. Frequency Response: 40Hz - 300Hz.
Size(inch): (W)21-9/10" x (H)7-1/3" x (D)13-3/8. 4 ohms 70W x 2. 2 ohms 85W x 2. Bridged 4 ohms 170W x 1.
Signal to Noise Ratio: 100dB. Filter: 80Hz -18dB / oct. Size(inch): (W)9-1/16" x (H)2-3/16" x (D)6-9/16. THIS PRODUCT REQUIRES PROFESSIONAL INSTALLATION.The item "Kenwood P-W121B 2 Inch Car Loaded Sealed Subwoofer & 500W Amplifier Package" is in sale since Sunday, November 11, 2018. This item is in the category "Consumer Electronics\Vehicle Electronics & GPS\Car Audio\Car Subwoofers". The seller is "turacell" and is located in Brooklyn, New York. This item can be shipped to United States, Canada, United Kingdom, Mexico, Germany, Japan, Brazil, France, Australia, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Greece, Portugal, Cyprus, Slovenia, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Austria, Bahamas, Israel, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Chile, Colombia, Costa rica, Dominican republic, Panama, Trinidad and tobago, Guatemala, El salvador, Honduras, Jamaica, Viet nam.