LOADED SUBWOOFER BOX 2x 12 3000 WATTS + BASS3000 1 OHM AMP TIMPANO BASS BUNDLE
Car Audio Subwoofer Box Loaded Ported Enclosure with 2x. 3000 Watts Car Audio Bass Amplifier. The most popular option for premium loaded enclosure package by Timpano makes it easy to add low-frequency bass to your vehicle. Two 12 inch dual 4 Ohm.
Subwoofer is included in this package, pre-wired inside the enclosure using 12 gauge copper wire for a 1 Ohm final impedance + one. This special box design features a kerf port, typically only seen in custom enclosures. The port is designed to reduce air turbulence, allowing the air to move out of the enclosure quickly and without any resistance. This results in a more powerful and efficient bass response.
This enclosure is made from MDF and reinforced with internal bracing for maximum durability. It is covered in high-grade carpet for a professional appearance.A slanted back allows the box to fit into most vehicles easily. Series was designed to bring the ultimate combination of performance, durability, quality and value. Featuring incredible linear excursion, with top-grade soft parts, American Made voice coils on a colossal cast aluminum styled basket creating a new standard for powerful systems. Its double stacked magnet motor drivers a 3?
American made 4-layer CCAW coil on a black aluminum former all coated with high temperature black adhesive. A stiff reinforced non-pressed treated paper cone & high roll foam surround was used to ensure performance on the lowest tones of bass.This monoblock Car Audio amplifier is designed to run your system with the power it needs to perform! Exclusive for BASS and SUB BASS applications. Its high efficiency provides more power with less battery consumption. Heavy duty power and speakers terminals. Built-in variable crossover filters for easy tuning!
Set setting for your subwoofer with a SUBSONIC filter 8 to 40Hz and LPF 30 to 250Hz without a need for an external crossover or DSP. Fine tune it according to your box with variable frequency dial and BASS BOOST at choose frequency up to +10 dB. It also includes Variable Gain Control.Level controls are not for adjusting volume. They adjust the amount of signal that is coming into the amplifier from your signal source. This sub is conservatively rated of 2,500 watts peak power / 1250 watts RMS guaranteeing to put out some crazy output. Equipped with a robust double-layered spider with, stitched-on XL tinsel lead wires, to hold a longer play time, maximizing durability. Bassheads searching for more lows!
You can look forward to deep, Low, impact bass in a small enclosure with a generous 1.85? Xmax of 23.5 mm one-way and Max Xmech of 37 mm one-way.
TPT2500-12 D4 is a quality sub that fits in any audio enthusiast's budget. Dual 4 Ohm American made voice coils. A chrome vented back plate and unique vented basket design enhances heat dissipation.
Stitched cone reinforcement ensures long life. Timpano T2500 series subwoofer box will play deeper, with more dynamic range and increase output, after you properly break in your subwoofer. Its suspension is designed to provide a high level of excursion and linear control in ported boxes. A brand new sub will be a little stiff, but with a proper break in, the subwoofer soft parts will stretch out! Which means with less power power you will create the same output with more extended low bass tones.
Kerf Port (Flared Slot Port). 15.25" H x 37.75" W x 16.75 Deep. Amplifier TPT-BASS3000 1 Ohm Specifications. Number of Channels: 1 3000 Watts RMS Power at 1 Ohm 14.4Volts 1800 Watts RMS Power at 2 Ohm 14.4 Volts Supply Voltage: 9V 17V Frequency Response: 8Hz 600KHz Flat Switch - ON (no Crossover Filters) 8Hz 600Hz Crossover Low Pass Filter: 8Hz 250KHz Crossover Subsonic Filter: 8Hz 40Hz Bass Boost Freq: 30Hz 70Hz Bass Boost Gain: 0 dB +10 dB Signal to Noise: > 90 dB Impedance Output: 1 Ohm Musical Consumption: 132A Bass Consumption: 265A Dimensions (L x W x H): 9.36" x 9.03" x 3.05 Weight: 6.14 Lbs.You must follow the instructions for the product's installation and connections to guarantee optimal performance. If you have any questions, get in touch with us. Before using the amplifier, always follow these guidelines. Make sure the amplifier is switched off before adding or removing any connections.
This prevents possible damage to the equipment connected to the amplifier. Keep all cables as far away as possible from the ignition cables, electronic injection modules and starter switch since they may cause noise interference.
Always use 100% Copper cables and good quality connectors. This guarantees the sound's quality and fidelity.